飛利浦BVP431 BVP432 BVP433 LED投光燈安裝說明：
1. No sharp edge on the interface (bracket or hole) of mounting side.
安裝側接口無銳邊（支架或孔）
2. For below status, must replace the safe chain by a new one instantly：
發現下面情況之一，安全鏈必須由一根新的安全鏈替換。
a, The safe chain was tightened one time by luminaire falling;
安全鏈承受過燈具墜落負荷繃緊。
b, Part of steel wire was broken；
安全鏈鋼絲有部分斷裂損壞。
c, While replace the luminaire, the safe chain is a falling protector, not
allowed to suspend the luminaire by a long time.
安全鏈是防墜落保護器具，在替換燈具期間不允許長時間懸掛燈具。
供應飛利浦BVP431 BVP432 BVP433 LED投光燈安裝說明
Warning
警告
1. The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEEE electrical regulations or the national requirements.
燈具必須由獲得電氣資格證書的人員安裝和接線，并且符合遵守新的IEEE電氣規章或國家標準要求。
2. Switch off main power supply before Installation, maintenance and any operation.
安裝，維護和操作燈具等設備前，請切斷電源主供應
3. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
此燈具內的光源應由制造商或其服務代理商或一個類似的有資格的人來更換。
4. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar
qualified person in order to avoid a hazard. (only for luminaire itself with cable sold, must be compliance this clause.)
如果燈具的外部電纜線或軟纜線被損壞，必須專門由制造商或授權的代理商或一個類似獲得資格證書的人員替換，以避免任何可能對人員的
傷害。（僅對燈具本身自帶電纜線或軟纜線必須遵守和符合本條款）
5. Use IP66 grade connection devices with cable clamp to ensure a complete IP66 system.
使用IP66等級的連接裝置和設備并攜帶電纜防水夾緊接頭來保證完整的IP66系統等級性能。
6. Refer to technical datasheet for additional electrical properties to ensure installation safely.
涉及到額外電性能技術數據表來安全地保證安裝和施工
7. Ensure power supply cables (L-N / L-N-E) are connected correctly before switching on.
合上電源燈具等設備通電前，請務必確保供應電纜線和接地線 (L-N / L-N-E)被正確地連接。
8. The insulation of category between LV and control circuit is to relay on type of driver.
LV電源和控制線路之間的絕緣類型取決于驅動型號。
9. The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than m is not expected.
燈具的安裝位置應使其不會長時間在小于 m的距離被盯著看.
10. Earthing contact to customer end on luminaire must be connected by installer, including whole use process that the earthing contact is always reliably
linked to earth ground.
燈具上供客戶端接地點必須由安裝人員可靠地連接，并且在整個燈具使用過程中燈具接地點總是可靠地與大地連接。
11. The luminaire should avoid storage and usage in such a surroundings or an occasion that is with corrosion or hazardous gases like sulfide, halide,
phthalate and so on.
燈具應避免在有腐蝕或有害氣體環境和場合下儲存和使用，像硫化物，鹵化物鄰苯二甲酸鹽等。
12. The PC material cannot be used in such an ambience that is with ethylamine, tetra-dichloroethylene, which is corrosion or hazardous to PC material
and so on.
PC材料不能被使用在含有，四氯乙烯等這樣對PC材料有腐蝕或傷害環境下。
13. All materials used in luminaire must be compliance to RoHS as below table.
用在燈具里的所有材料必須遵守和符合像下面表格中的RoHS要求
供應飛利浦BVP431 BVP432 BVP433 LED投光燈安裝說明Maintenance
維護
1. Periodic clearing of the luminaires’ optical lens covers will ensure maximum optical efficiency.
定期清洗燈具的光學透鏡蓋以保證光效輸出。
2. Luminaire optical lens cover shall be cleaned with clean water, non-abrasive soap, cleaner and detergent solution. Acid solution or alkali solution
cannot be used as a cleaning solution to wash outside surface of luminaire.
燈具光學透鏡必須用清潔的水、非損傷性的肥皂、清潔劑和洗滌劑溶液。酸溶液或堿溶液不能用作清潔溶液來沖洗燈具的外表面。
Caution
供應飛利浦BVP431 BVP432 BVP433 LED投光燈安裝說明
注意
1. Luminaire must be used within the applicable product specification of installation instruction and environmental conditions for storage and operation
according to application guidelines provided by Signify for valid product warranty.
LED投光燈按Signify提供的燈具產品應用指南和有效的產品保修期規定，燈具儲存、操作和運行必須使用在合適的產品規格、安裝指導說明和環境條件范圍之內。
